Congratulations to my wonderful spouse and favorite hiking partner, Joyce/K0JJW, for achieving Mountain Goat status for Summits On The Air (SOTA).
Joyce/K0JJW on Pikes Peak, working a pileup as she qualifies for Mountain Goat.
On August 10th, she reached 1000 activator points while activating Pikes Peak (W0C/FR-004). She had quite the pileup on 146.55 MHz. Her best DX for the day was WY7ATH near Cheyenne, WY at a distance of 167 miles. Not bad!
Early on, she always hiked with me on SOTA activations but didn’t start pursuing activator points until the middle of 2017. All of her SOTA contacts have been on the VHF/UHF bands, lots of 2m FM along with 2m SSB, 70 cm and 23 cm FM.
Joyce has activated 181 summits, 112 unique in 19 associations.
She is the second female Mountain Goat in Colorado (after Lynn/KC0YQF) and is the eighth female goat in North America.
McQuaid Butte (W0C/SP-019) is a 9043-foot mountain near our cabin in Park County. Joyce/K0JJW and I activated it for Summits On The Air (SOTA) way back in 2013 but for some reason, we had not been back to it. The access road (Salt Creek Road, FS 435) is gated closed from January 1 to June 15 to protect wildlife habitat, so I suppose that is a factor.
McQuaid Butte (W0C/SP-109) as viewed from the south.
Today, we decided to make a return trip to the summit and activate it on VHF/UHF. I remembered that Salt Creek Road can turn into a muddy mess but today it was dry and easily drivable with most vehicles. Salt Creek Road is accessed from Highway 285, south of Fairplay but north of Antero Junction.
Access to McQuaid Butte is via Salt Creek Road, from Highway 285. The hiking route is shown in blue.
There is a good parking spot shown on the map above at 38.95791, -106.00790. A trail begins here, heading east. It used to be 4WD road but it is now closed to motor vehicles. This trail/road heads east and then curves to the north and eventually disappears. About that time, you’ll encounter a fence that needs to be crossed as you make your way towards the summit (approaching from the west). There are pieces of a trail here and there but its mostly bushwacking up the side of the summit. In places, there is substantial downed timber that can be stepped over and around but its mildly annoying.
Bob/K0NR relaxing on the summit.
Our route turned out to be 1.3 miles one way with 650 vertical feet. We both quickly made enough QSOs to qualify for activator points, working W0BV, KD0MRC, K0MGL, WZ0N on 2m FM (and some on 70 cm). The weather was excellent, resulting in a fun SOTA activation in the Pike National Forest.
We will probably return again to this summit because it’s a nice hike that is easy to get to from our cabin. It would also be a great choice for someone passing through on Highways 24 or 285.
In 2018, Joyce/K0JJW and I did a trip to the Black Hills area of South Dakota to do some SOTA activations: Dakota SOTA Adventure. We really enjoyed that part of South Dakota and figured we would be back. The Black Hills top out at ~7200 feet and the climbs are usually interesting but not very difficult. There are plenty of SOTA summits to choose from and the scenery is beautiful.
Bob/K0NR and Joyce/K0JJW standing in front of their RV (Winnebago Paseo). Photo: K0DAJ
This summer we found ourselves on a road trip returning to Colorado from Wisconsin, so we decided to swing by South Dakota for a couple of days. Joyce is getting close to achieving the coveted SOTA Mountain Goat award (1000 activator points), so we were looking to add to her activator score. I’m not saying we only did easy summits but we pretty much did easy summits.
Looking at the SOTA database, we scanned for summits with 6 points or higher that also had a significant number of activations. On this trip, we were driving our Class B RV (basically a big honkin’ van with RV gear in it). This limited our choice of SOTA summits to ones that can be accessed via reasonably good roads. We were fine with the typical gravel US Forest Service road in good condition but not anything worse.
We connected up with Don/K0DAJ who we met at a hamfest in Loveland, CO earlier this year. Don reviewed my list of potential summits and provided valuable feedback and additional summit suggestions. Don also alerted the local hams that might want to get on the air to work us. We use VHF/UHF exclusively for SOTA, so it is easy to get skunked if there isn’t anyone around. (I found out later that Gary/KT0A also passed along the word for us.)
The SOTA Summits
We identified seven summits that we wanted to activate, which would provide 56 new activator points. They ended up being clumped into three northern summits, around Deadwood, and four southern summits southwest of Rapid City. We camped at a USFS campground in between the two clumps, activating the northern three on the first day and the southern summits on the second day.
A map showing our seven SOTA summits in the Black Hills area.
Terry Peak (W0D/NW-002)
Terry Peak is a drive-up mountain with a short hike up to an observation platform. We approached Terry Peak from the south on Terry Summit Road, off of Hwy 85/Hwy 14A. The Black Hills National Forest map is very helpful for finding all of these summits.
We discovered that Terry Peak is quite the tourist spot and several groups of people showed up while we were there. It is also a big radio site with over a dozen towers and many more transmitters. When we parked, I noticed that the VHF/UHF mobile transceiver in the RV had both S meters pegged at full scale on all frequencies. Rut Roh, there is probably some RF around here. As usual, we had the Yaesu FT-90 transceiver which has a robust receiver in it, and it performed well. Still, I noticed that strong signals would abruptly drop down to being almost unreadable when some transmitter on the site turned on.
Bob/K0NR operating 2m FM on Terry Peak, using the Arrow 3-element Yagi antenna.
Mount Theodore Roosevelt (W0D/NW-023)
Mount Theodore Roosevelt turned out to be a pleasant surprise with a really good trail to the summit (0.4 miles one way, less than 200 feet elevation gain).
The trail as it just leaves the parking lot area.
Also, at the summit, there is a tower that was built in honor of President Roosevelt. This is a fun little hike with a monument at the summit.
We climbed the stairs leading to the top of the tower and operated from inside it. The tower reminds me of the many lighthouses we’ve been inside, but it’s not nearly as tall, and no light.
Bob/K0NR working 2m FM from inside the tower.
Unnamed Summit – 5110 (W0D/NW-038)
For a third summit, Don suggested an easy-to-access unnamed summit (5110), W0D/NW-038. We got there by driving south from Sturgis on Vanocker Canyon Road (26), then west on Galena Road to USFS 171.1. Driving a short distance north on 171.1 got us to an open area where we parked. Then it was just a bushwack up the hill (no trail), 0.3 miles one way with an elevation gain of 400 feet.
Location map of W0D/NW-038. The blue line is the hiking path that we took to the summit.
Second Day
Day 2 was a repeat of summits that we did in 2018, so I won’t repeat all of that here: Odakota Mountain (W0D/BB-002), Bear Mountain (W0D/BB-029), Coolidge Mountain (W0D/BB-012) and Rankin Ridge (BB-089). Refer to the 2018 trip report for more info.
This time, Odakota Mountain was extra special because Don/K0DAJ joined us on the summit.
Don/K0DAJ and Bob/K0NR at the parking spot for Odakota Mountain.
There is an actual summit marker for Odakota, so I had to get a photo of me standing there.
Bob/K0NR standing at the Odakota Mountain High Point marker.
Most of the contacts were on 146.52 MHz, a few on 446.0 MHz. Joyce’s log and my log are pretty much the same but I did work a few more stations. In summary, we had QSOs with these stations during the two days: AD0HL, K0DAJ, KB0QDG, KC0WC, KD0AYN, KF0AFX, KF0ARA, KF0XO, KF7ZQL, NC0K, W0LFB, W0NIL, W0SEB, W0SSB, W5LJM, W7LFB, WN6QJN and WS0V. Thank you to each and every one of you for getting on the air!
In Colorado, we pretty much work Colorado stations on VHF from the summits, so it was fun to contact other states on this trip. From Bear Mountain, we worked W0NIL and W0SSB in Chadron, NE, about 90 miles away. Not too shabby. From Terry Peak, we worked Clem/KF7ZQL in Carlile, WY at a distance of 50 miles. Not as far, but another state in the log.
We caught AD0HL and KF0ARA on unnamed summit 6167 (W0D/BB-008) from both Odakota Mountain and Bear Mountain, for two Summit-to-Summit (S2S) contacts. We also got two S2S contacts with Don/K0DAJ: Crooks Tower from Terry Peak and Terry Peak from Mount Theodore Roosevelt. It was kind of an S2S festival!
Don/K0DAJ and Terry/AD0HL worked us on 6 of the 7 summits, so they were our most prolific chasers. Thanks, guys! Finally, special thanks to Don for the helpful advice and joining us to play radio in the Black Hills.
We were able to get our minimum 4 QSOs on each summit and usually had many more. This resulted in 56 activator points, so we are quite happy with that. We have just sampled a few of the many SOTA summits in the Black Hills area, so I suspect that we will be back for more.
Amateur Radio operators from around Colorado will be climbing many of Colorado’s 14,000-foot mountains and Summits On The Air (SOTA) peaks to set up amateur radio stations in an effort to communicate with other radio amateurs across the state and around the world. Join in on the fun during the 29th annual event and see how many of the mountaintop stations you can contact. The covers the entire weekend but many mountaintop activators will hit the trail early with the goal of being off the summits by noon due to lightning safety concerns.
The event includes all Summits On the Air (SOTA) summits, which adds over 1800 potential summits! If you aren’t up to climbing a 14er, there are many other summits to choose from with a wide range of difficulty. See the Colorado SOTA web page at w0c-sota.org
Radio operators who plan to activate a summit should post their intent on the ham14er group via the ham14er groups.io website. Also, be sure to check out the event information at http://www.ham14er.org
Frequencies used during the event Activity can occur on any amateur band including HF and VHF. The 2m fm band plan uses a “primary frequency and move up” approach. The 2m fm primary frequency is 147.42 MHz. At the beginning of the event, operators should try calling on 147.42 MHz. As activity increases on that frequency, move on up the band using the 30 kHz steps. Don’t just hang out on 147.42 MHz…move up! The next standard simplex frequency up from 147.42 MHz is 147.45 MHz, followed by 147.48 and 147.51 MHz.
For a complete list of suggested HF, VHF and UHF frequencies see this web page.
Warning: Climbing mountains is inherently a dangerous activity.
Do not attempt this without proper training, equipment and preparation.
There is a lot more information available here: www.ham14er.org
Sponsored by The Colorado 14er Event Task Force
Also be aware that the SOCAL SOTAFEST is happening on the same weekend, which means there will be plenty of SOTA activity on the ham bands! See http://socalsota.com
Way back in 2013, Joyce/K0JJW and I did the first SOTA activation of W0C/SP-099, an unnamed summit in the San Isabel National Forest. As is often the case, we just reviewed the forest service map and drove down a road that got us sort of close to the summit and headed on up. On this initial activation, we came from the south, which is a viable route, but not all that great. Later, Walt/W0CP found a much better starting point to the east of the unnamed summit, so we were interested in trying that out.
The driving directions are to take County Road 187 south to CR 185, then turn off onto 185E. Consult the San Isabel National Forest map for context. The graphic below shows the immediate area near the summit.
The blue line shows the hiking route to SP-099.
The only mildly tricky part of FS 185E is that it passes through a section of private property that is surrounded by national forest. There are a number of private drives along the road (most of them gated and labeled “No Trespassing.”) However, 185E keeps on going and pops out the other side, where a wire gate marks the reentry into the national forest. Walt indicates a good place to park is at Lat/Lon 38.78067, -105.98301. The road was in good condition and should be passable with a high-clearance 2WD vehicle.
At this point, headed west towards the summit, hiking off trail. There is very little downed timber so the walk is quite enjoyable. The specific route is not critical but stay north of the private property.
Typical terrain and vegetation heading towards the summit.
My GPS app shows the hike at 0.85 miles one way with 460 feet of elevation gain. This is easy peasy, so we have started to call this unnamed summit “EZ 99”.
Joyce/K0JJW hiking near the summit.
We worked a number of stations on 2m FM and then headed on down. (We also activated Bald Mountain W0C/SP-115, about two miles west, on the same day.)
This summit is now on our highly recommended list, an easy-to-access, pleasant hike in a beautiful area of Colorado.
I am excited to announce the release of my new book: VHF, Summits and More.
This book is about having fun with ham radio, primarily on the VHF/UHF bands. It covers the basics of VHF, with practical tips for getting on the air and “messing around with radios.” Topics include FM, SSB, repeaters, equipment, band plans, phonetics, portable operating, Summits On The Air (SOTA) activations and more. This book is a compilation of the best articles from the k0nr.com website plus some brand-new material.
The first section explains VHF/UHF concepts via tutorial articles such as “VHF FM Operating Guide,” “Getting Started on 2m SSB” and “How to Work a VHF Contest.” The second section includes blog posts from the k0nr.com website, such as “Choose Your 2m Frequency Wisely,” “VHF Grid Locators,” “Phonetic Alphabets” and “VHF FM: The Utility Mode.” The final section helps the reader understand mountaintop operating, especially Summits On The Air (SOTA) activations, including operating tips and trip reports.
The book is available from Amazon, in paperback and Kindle formats. The normal price for the print version is $22.95, but there is an introductory price of $15.95 through November 18th. The Kindle version is $9.95.
While looking for our next SOTA adventure, I noticed a never-been-activated, unnamed 13er (W0C/SP-020) to the west of Mount Princeton. I checked various maps and it looked like there was a 4WD forest service road that went up to the adjacent saddle. So Joyce/K0JJW and I decided to give it a try.
SP-020 as viewed from the saddle (and parking spot).
We took County Road 306 west out of Buena Vista, towards Cottonwood Pass. Then we turned left onto County Road 344 which goes to Cottonwood Lake. We continued past Cottonwood Lake until we found FS 348, also known as Hope Gulch Road. We followed this road for 5 miles to the saddle.
This graphic shows the 4WD road in red and the hiking route in purple.
The road was easy-peasy 4WD, no problem at all with our stock Jeep Wrangler. A Suburu-class SUV can probably make it but there are a few rocky spots on the road that will require special care. There were two water crossings, one of them with about a foot of water (across Cottonwood Creek). Now this was mid-October, so the streams are not running real strong. Earlier in the year, this could be a major hazard.
Warning: water crossing at Cottonwood Creek.
A closeup view of the hiking path (0.6 miles, 800 feet vertical)
FS 348 is single lane, with long stretches without an easy passing or turnaround spot. We were happy that we only saw two other vehicles on the road.
Talus
We drove a bit past the saddle (where there is a small hut/cabin) and parked where a closed side road heads off toward the summit. We hiked up this closed road and then vectored off towards the summit. The hike was only 0.6 miles and 800 vertical feet. However, there was quite a bit of talus (rock debris) to climb over which really slowed us down. The hiking route does not seem critical but following the top of the ridge seemed to be good.
Near the top, we encountered lots of talus.
Yeah, about the talus. It isn’t any worse than other rocky summits in Colorado but it seemed to catch our attention, usually in the form of “ok, I’ve just about had it with this talus.” A contributing factor was that both Joyce and I had foot/ankle injuries in recent years. So our unofficial name for this summit became Talus.
Joyce/K0JJW on the summit of W0C/SP-020A pile of gear at the summit.
Joyce/K0JJW took the honors of completing the first SOTA activation of this summit by contacting Bob/W0BV on 2m FM. We also both logged these stations: KD0MRC, W0RW, W6JM, W0LSD and N0AJN.
Bob/K0NR operating 2m from the summit, wearing orange during hunting season.
We sat there quite a while just taking in the view. Mt Princeton is due east; Mt Antero and Mt White are to the south.
The view of Mt Princeton, five miles east of SP-020.
You never know what your gonna get on the first activation of a summit. On this one, it turned out to be a fantastic day. The weather was sunny, temperature about 40 degrees, a little too windy at times. Late in the season, we didn’t have to worry about thunderstorms moving in and blowing us off the mountain. I liked the combination of a good 4WD road, heart-pumping but not-too-difficult hike, a first-time SOTA activation and doing it all with my favorite hiking partner (and wife).
View from the summit of Mt Herman, looking out over the eastern plains.
Access to the summit is not difficult and most of the locals know how to find it without a problem. However, there are a few things that can trip up a first-time activator.
Most people will get to Monument via I-25, taking the main Monument exit (Exit 161). Go west on 2nd street through the old downtown area, over the railroad tracks to a stop sign at Mitchell Road. Go left (south) on Mitchell Road and then right (west) onto Mount Herman Road (FS 320). Shortly after entering the national forest, you will probably see a sign that says Mt Herman Trailhead. THIS IS NOT THE TRAILHEAD YOU WANT. Keep going on Mt Herman Road.
Mt Herman Road angles left (going south) at the intersection with Red Rocks Drive. At this point, reset or check your odometer as it will help you find the actual Mt Herman Trailhead (see map). Continue on Mt Herman Road for 2.6 miles, where the trailhead is off to the right as the road curves left.
The condition of Mt Herman Road varies considerably from year to year. Most of the time the road is OK for high-clearance 2WD vehicles. Sometimes it deteriates to easy 4WD. The road and trail are often usable in the winter months but it depends greatly on recent temperatures and snowfall. The road is not maintained in the winter so definitely 4WD required.
Trailhead
The actual trailhead is not that well marked, hence the need to watch the odometer. However, on most summer days, there will be cars parked at the trailhead. Parking is informal, just a gravel area off on the right side of the road.
The red line shows the trail to the summit.
The trail to the summit is 1.2 miles one-way and 800 feet vertical. Make sure you stay to the right about 500 feet from the trailhead, on a trail that takes you up the mountain. There is another trail that continues straight at this point, which may throw you off. You should soon encounter a steep switchback at this point as you start to work your way up the mountain (see map above).
The trail is usually in decent shape with a few steep sections where the loose granite marbles can make it slippery. Hiking boots with some tread on them are recommended and trekking poles can be helpful, too.
Typical trail section with Joyce/K0JJW hiking it.
At the summit, there is a fire ring where people sometimes camp out overnight. The hike is popular, so you’ll probably have other people stopping by. There is plenty of room in the activation area, so I set up my radio gear some distance from the actual summit.
Mt Herman is a wonderful hike with great views (even if you don’t want to do a SOTA activation). With a superb radio horizon, it is also first-rate place to make radio contacts.
SP-089 has a large rock face on the south/southwest side, so it is best to approach from the other side.
Back in 2014, Joyce/K0JJW and I did the first activation of W0C/SP-089 (also known by its elevation: 10525). See the trip report here.
As noted in that trip report, we never did find much of a trail so we had to do some serious offtrail bushwacking. Being on the summit was great but bushwacking up was not. Later Walt/W0CP found a much better route using the Davis Meadow Trail. We definitely wanted to try this route and get back on top of that summit.
This overview of the area shows the route we took up SP-089 in blue and the Davis Meadow Trail as shown on the Trails Illustrated map.
We approached the Davis Meadow Trailhead from the east via Highways 285 / 24. We took FS 311 from Trout Creek Pass to FS 373, then FS 373A. FS 311 starts out in good condition, passable by high clearance 2WD vehicles. Later it turns into “easy 4WD” but it gets very steep in spots which may be a problem during wet weather. You can also approach from the west side coming up from Buena Vista. Check the San Isabel National Forest map for the complete picture.
Just to the east of the unnamed summit is a natural arch, marked on some maps as Aspen Arch. We’ve hiked up the arch on numerous occasions, often with visitors from out of state. So we’ve started referring to this unnamed SOTA as Aspen Arch, to differentiate it from the other unnamed summits in the area.
SOTA summit W0C/SP-089 is also known by its elevation (10525). A nearby landmark is Aspen Arch.
The Davis Meadow Trailhead is marked by a sign. Trail 1413 heads north and loops around the north side of SP-089. The trail is well laid out with plenty of switchbacks, much more than indicated on the Trails Illustrated map.
The blue line shows our actual hiking route as tracked by my GPS app.
We followed the trail until it looped around the north side of SP-089. Marmot Peak, another SOTA summit (W0C/SP-063), sticks out prominently to the north and is a good landmark to use for navigating. As shown on the map above, we left the trail and bushwacked south up to the summit. I don’t claim that our route was optimal. It was classic offtrail hiking with some areas quite open and others clogged with plenty of downed trees and rocks. (Next time, I think we’ll try to stay a little further east of our recorded track. It looked a little better over there.) Expect to be slowed down during this stretch.
Joyce/K0JJW on the well-established Davis Meadow Trail.
The GPS app on my phone recorded the one-way hike as 2.7 miles and 1100 vertical feet.
This was typical of the downed timber on the bushwack portion of the hike.
We arrrived at the summit around noon and thunderstorms were moving into the area. We both made four quick radio contacts on 2m FM to get the activation points, then headed back down the trail. The summit is exposed and very rocky but once we got off the top, we were hiking in trees with limited lightning danger. Thanks to Bob/W0BV, Jim/KD0MRC, Larry/KL7GLK and Kevin/KD0VHD for working us.
After our first bushwack adventure on this summit, we were not motived to activate this one again. However, using the Davis Meadow Trail has changed our opinion. (Thanks Walt/W0CP!) This route still has some offtrail bushwacking but it is not bad. We will be back!
When planning for the next Summits On The Air (SOTA) hike, I want to understand the difficulty of the climb. The main things to evaluate are the length of the hike (horizontal distance), the vertical (elevation) gain and other contributing factors.
Most of the SOTA summits in Colorado have a simple profile: pretty much uphill on the way to the summit and then mostly downhill on the way back to the trailhead. Yes, there may be flat sections and sometimes there will be a downhill section or two on the ascent, which means you give back some elevation gain only to regain it later. Usually, we think of going downhill as “easy” but if you have sensitive knees or other joints, you may disagree.
The first question is how far do I need to hike? Clearly, hiking 10 miles is a lot harder than hiking 1 mile, all other things being equal. However, I usually find the vertical gain to be more important. (Typically, the horizontal distance of a SOTA hike is within my capabilities and the vertical gain is the thing that wears me out.) I also do a back-of-the-envelope calculation on slope. My benchmark for slope is 1000 vertical feet in one mile, which is an uphill slope that will get my heart pumping but is not too difficult (corresponds to ~20% slope). Anything steeper than that starts to feel more challenging. A slope less than that is easier. Be careful with average calculations. You might find that a particular trail is flat for 3 miles and then gains all of the vertical in the last mile. Having a good topographical map is a must for understanding the route. I generally use GAIA GPS, an online mapping website and smartphone app.
Certainly the condition of the trail and its inherent terrain are an important factor to consider. The SOTA hikes I do are typically Class 1, 2 or 3. I don’t do summits that require ropes or technical climbing.
Class 2. More difficult hiking that may be off-trail. You may also have to put your hands down occasionally to keep your balance. May include easy snow climbs or hiking on talus/scree. Class 2 includes a wide range of hiking and a route may have exposure, loose rock, steep scree, etc.
Class 3. Scrambling or un-roped climbing. You must use your hands most of the time to hold the terrain or find your route. This may be caused by a combination of steepness and extreme terrain (large rocks or steep snow).
Example summits
Let’s take a look at some specific summits as examples.
Note: there are often multiple routes to the same summit, so don’t use this information for trip planning. Do your homework.
Mt Herman (W0C/FR-063): a bit steep in spots but typical of many SOTA hikes: 1000 feet vertical gain in about one mile, right at my benchmark of 1000 feet vertical per mile. I consider that an easy hike.
Genesee Mountain (W0C/FR-194): is one of the easiest and enjoyable SOTA summits in Colorado, only 0.7 miles and 300 vertical feet. The average slope is 430 feet per mile, so not very steep at all.
Mt Sherman (W0C/SR-061): is considered to be one of the easiest fourteeners, but it is still a fourteener: 2100 feet vertical gain in 2.6 miles (807 feet per mile).
Mount Elbert (W0C/SR-001): A more challenging (middle of the road?) fourteener with 4700 feet vertical gain over 4.75 miles). The average slope is 1000 feet per mile so it’s not that steep but 4700 vertical feet will definitely wear me out.
Other Factors
Not to be overlooked, the condition of the route can make a big difference. Often, there is no established trail to a SOTA summit, which means you’ll need to hike offtrail or “bushwack”. If the ground is uncluttered and the trees well-spaced, bushwacking can be easy. On the other hand, if there is a lot of downed timber, you have to climb over and around obstacles to get to the summit. Some summits have willows or other scrub brush that gets in the way. Intense bushwacking can make a huge difference, making the hike more difficult by a factor of two (or more). Many times, I’ve looked at the route to a summit on a topographical map, judged it to be not so bad and later discovered that it requires serious bushwacking. Hikes like that really help me to appreciate a well-designed and maintained trail.
High altitude and the resulting lack of oxygen contribute to the difficulty of the climb. This is going to vary considerably between individuals. Almost everyone feels the effects at 14,000 feet but at lower elevations individual performance will vary dramatically. Normally, I don’t have an issue at 10,000 feet, notice some effect at 12,000 feet and I’m definitely huffing and puffing above 13k.
Finally, weather can play a big role in increasing the difficulty of a hike. In the winter, it is common to use snowshoes when deep snow is present on the route. The snowshoes tend to sink into the snow with each step, causing more effort to be expended hiking the route. Ice can also be present requiring microspikes or other traction devices. Icy conditions tend to slow you down and can be a safety issue.
So that’s a quick look at how I judge the difficulty of a SOTA hike. The SOTA database often has trip reports from other SOTA activators, which can be extremely helpful. It is always great to learn from the experiences of other folks. I can’t tell you how difficult a climb will be for you because your physical abilties are likely different than mine. But taking note of the factors mentioned in this post will help you develop a sense of how difficult a summit is for you.
Amateur Radio operators from around Colorado will be climbing many of Colorado’s 14,000-foot mountains and Summits On The Air (SOTA) peaks to set up amateur radio stations in an effort to communicate with other radio amateurs across the state and around the world. Join in on the fun during the 28th annual event and see how many of the mountaintop stations you can contact. The covers the entire weekend but many mountaintop activators will hit the trail early with the goal of being off the summits by noon due to lightning safety concerns.
The event includes all Summits On the Air (SOTA) summits, which adds over 1700 potential summits! If you aren’t up to climbing a 14er, there are many other summits to choose from with a wide range of difficulty. See the Colorado SOTA web page at w0c-sota.org
Radio operators who plan to activate a summit should post their intent on the ham14er group via the ham14er groups.io website. Also, be sure to check out the event information at http://www.ham14er.org
Frequencies used during the event Activity can occur on any amateur band including HF and VHF. The 2m fm band plan uses a “primary frequency and move up” approach. The 2m fm primary frequency is 147.42 MHz. At the beginning of the event, operators should try calling on 147.42 MHz. As activity increases on that frequency, move on up the band using the 30 kHz steps. Don’t just hang out on 147.42 MHz…move up! The next standard simplex frequency up from 147.42 MHz is 147.45 MHz, followed by 147.48 and 147.51 MHz.
For a complete list of suggested HF, VHF and UHF frequencies see this web page.
Warning: Climbing mountains is inherently a dangerous activity.
Do not attempt this without proper training, equipment and preparation.
There is a lot more information available here: www.ham14er.org
Joyce/K0JJW and I were planning a trip to Alaska to visit several of the national parks. We had some time available while in Fairbanks to do some SOTA activations. We were traveling very light, so we took minimal SOTA gear: a pair of VHF/UHF handhelds and simple antennas.
The lightweight VHF/UHF SOTA outfit: Just a pair of Yaesu FT-1DR handheld transceivers, spare battery and basic antennas (rubber duck and RH 770).
We used my newly-fashioned antenna mount on a trekking pole we had with us. The trekking pole served us as as a trekking pole for hiking, a camera monopod and now an antenna support. It provides a handy way of supporting a vertical antenna and provides a little more antenna height when held up in the air.
The trekking pole with antenna mount attached. An RH 770 antenna attaches to the BNC connector on top.
I checked the SOTA database to identify easy-to-access summits near Fairbanks. There are several 1 and 2 point summits in the area with easy access. We were not looking for drive-up summits but we did want an easy hike.
I found that Dale/KL7R and Peter/K3OG had been activating in the area, so I contacted them via email and they both gave me helpful advice. We were a bit concerned about getting our four QSOs on VHF, but that turned out to not be a problem. We worked Dale from all three summits and he helped rustle up a few more stations to work. We had pretty good luck just calling CQ on 146.52 MHz. And I announced our presence and need for simplex contacts on the KL7KC repeater (146.88 MHz, 103.5 Hz tone).
We drove up Chena Ridge Road, then took a gravel road uphill towards the summit (I think it was labeled North Becker Ridge Road). At this point, we encountered a locked gate and parked there. Some locals wandered by and said that they hike up to the top every day, so come along. The hike was easy, less than one quarter of a mile with some elevation gain. At the summit is an FAA VOR site enclosed by a chain link fence.
Next, we drove north out to Pedro Dome, which has a substantial radio site on top. We took Steese Highway north from Fairbanks to Pedro Dome Road, a gravel road that goes right to the top of the summit. There are opportunities to make a wrong turn on the way up Pedro Dome Road but with a little care we were able to drive to the top. Despite the fact there are plenty of radio transmitters on the summit, we did not experience any interference on 2m and 70 cm. That summit has an excellent radio horizon, so it was easy to work stations in the Fairbanks area.
Bob/K0NR holds the trekking pole with RH 770 antenna attached, on Pedro Dome. The radio site is visible in the background.
Wigwam Benchmark is a summit that pokes up just north of Fairbanks. It is a bit more difficult to navigate because it in a rural residential area with lots of twisty-turny roads. I plugged “Noel Drive, Fairbanks, AK” into google maps, which got us very close. Then we drove to where Noel Drive meets Mia Drive and operated from the road. The area is heavily wooded and we did get attacked by the famous Alaskan mosquitoes, so we made our radio contacts and escaped quickly.
Summary
At one point, I told Dale that if we made one contact from one summit, we would be happy. But, of course, we tried for more than that and got it. It turned out to be a great day running around these summits near Fairbanks and making some radio contacts. Thanks to KL7R and K3OG for the assistance!
My Summits On The Air (SOTA) activation of Pikes Peak (W0C/FR-004) on June 20th qualified me for Mountain Goat, using only the VHF/UHF bands. Mountain Goat requires 1000 activation points using the SOTA activation point system.
Bob/K0NR operating from Pikes Peak on 20 June 2019 to complete Mountain Goat.
I’ve been working toward this goal for quite a while. I was doing mountaintop VHF activations before SOTA was even a thing. The first contact in my SOTA log is from Mount Antero in August 2011 but I started cranking up the SOTA activations in 2013 and later. I chose Pikes Peak for my qualifying Mountain Goat activation because its always been a special summit for me: I see it almost every morning (weather permitting) from my house in Monument. It is America’s Mountain, reaching to over 14k feet in elevation, standing tall west of Colorado Springs.
My custom Mountain Goat Award certificate made by Steve/WG0AT.
Most people have to wait for the mail to receive their SOTA Mountain Goat certificate. However, Steve/WG0AT created a custom award certificate that Joyce presented to me on the summit of Pikes Peak.
Paul/W0RW captured this webcam photo of Joyce/K0JJW and me standing near the summit house on Pikes Peak.
Some statistics from my SOTA log: I made 1557 radio contacts during 164 activations. Some of these activations were repeats of the same summit and I activated 96 unique summits. On 9 of those activations, I failed to complete the minimum of 4 radio contacts required to receive points; so I “got skunked” on those summits (zero points).
The majority of these summits were in Colorado, but I also did some operating from California, South Dakota, New Mexico, Wyoming, Utah, Oklahoma, Nebraska, Tennessee, North Carolina, Georgia, Arkansas, Texas and (last but not least) Switzerland. Almost all of them with my awesome wife and hiking partner, Joyce/K0JJW. Take a look at the various SOTA postings on my blog for trip reports and operating tips.
Chasers
Any SOTA activator will tell you that nothing happens without chasers being there to make radio contacts. Chasers are always important but even more important for VHF due to the limited range. The list below shows my top chasers. Some of these folks are active SOTA enthusiasts but many of them are just friendly folks on the radio helping me achieve this goal. You’ll see that my #1 chaser is Joyce/K0JJW, who usually worked me on multiple bands after leaving the summit.
Thank you, Chasers, for your support!
Many people underestimate what is possible on the VHF/UHF bands, even under normal conditions. I’ve been trying to educate folks on what is possible with VHF from high locations. See The Myth of VHF Line of Sight. Beefing up your station with a directional antenna and a little bit of power can make a big difference, even when just using FM. My best DX using VHF on a SOTA activation is a 2m CW contact from Capulin Mountain with W9RM near Olathe, CO for a distance of 257 miles.
The Summits On The Air program is a fantastic way to enjoy the outdoors while having fun with ham radio. Thanks to everyone that helped me reach my goal of VHF Mountain Goat.
For Summits On The Air (SOTA), I’ve been using just the VHF/UHF ham bands, with the 2m band being the most popular. For most activations, I use a 3-element Arrow II yagi antenna that has a gain of about 6 dBd. Sometimes that extra gain makes the difference between completing a contact or not.
Omnidirectional Antenna
The RH770 Dualband Antenna with BNC Connector
But it is also handy to have an omnidirectional antenna that is easy to deploy. Sometimes I’d rather just call or monitor using an omni without having to point the antenna. “Easy and good enough” can be an effective strategy for SOTA.
A key advantage to an omnidirectional antenna is that it is always pointed in the right direction.
I usually carry one of the TWAYRDIO RH770 VHF/UHF antennas for use with my 2m/70cm handheld transceiver. Despite its low cost, I have found that its performance to be quite good. That antenna is offered with a variety of connectors, including a BNC.
This led me to the idea of putting together a simple antenna mount with a BNC on it, attach an RH770 antenna to it and support it using some kind of pole. I have several monopod devices (intended for use as a camera support) that use the standard 1/4-20 thread. I also have a trekking pole that has the same camera mounting thread. Another option is to use an actual camera tripod which is a bit bulky but may work for some SOTA activations.
After a short visit to the hardware store, I selected crossbar for mounting a light fixture that was about the right size and shape. I happened to have a bulkhead-mount BNC-to-BNC connector which I inserted into the large hole in the crossbar. That hole was not quite large enough for the connector, but a few minutes work with a round file solved that problem.
After some filing to expand the hole, the bulkhead BNC connector (female-to-female) was inserted into the main hole in the crossbar.
The crossbar was originally flat but I bent one one end of it 90 degrees, with the idea that this might offer other mounting configurations in the future. For example, I might be able to strap or tape the 90 degree angle member to a pole or support.
The monopole support is inserted into one of the slots of the crossbar. Again, some filing was required to make the slot big enough for the 1/4-inch thread.
The other end of the crossbar has a large slot that accommodated the 1/4-20 mounting stud. Actually, the slot was not quite wide enough, so some addition work with a round file opened it up. I secured the 1/4-20 thread using a nylon wing nut.
A nylon wing nut (1/4-20 thread) is used to attach the crossbar mount to the monopod.
I’ve used this setup on one SOTA activation and was pleased with the results. I carried the crossbar mount attached to the monopod in my pack. On the summit, I simply installed the RH770 antenna onto the top BNC and extended the monopod. On this summit, I found the perfect pile of rocks that made a good support for the monopod. Then I used a short length of RG-8X coax between the bottom BNC and the 2m/70cm transceiver.
The antenna support in use: the RH770 antenna attaches to top BNC connector, the crossbar mount attaches to the monopole which jammed into a pile of rocks on the summit. An RG-8X coaxial cable feeds the antenna through the bottom BNC connector.
Although my primary interest was with the 2 meter band, it was really convenient to have both 2m and 70cm on the same antenna. I am pleased with operation of the antenna and the ability to deploy it quickly. I expect to carry this on most of my SOTA activations.
The conventional wisdom in amateur radio is that we should not call CQ when using FM on the VHF and UHF bands, especially on repeaters. The reasoning for this is that during normal VHF/UHF FM operating, radio amateurs are tuned to a specific frequency and will easily hear a call on FM.
Compare this to the HF bands, where the other ham is generally tuning around to find someone to contact and stumbles onto your transmission. In that case, you want to make a long call (CQ CQ CQ Hello CQ This is Kilo Zero November Romeo calling CQ CQ CQ…) so people tuning the band will find you and tune you in. On VHF/UHF FM, the assumption is that the other hams have their radio set on the repeater or simplex channel being used and will immediately hear you. FM communications are often quite clear and noise free, which also helps. The normal calling method is to just say your callsign, perhaps accompanied with another word like “monitoring” or “listening.” For example, I might say “KØNR monitoring.”
Question T2A09 in Technician exam pool reinforces this idea:
T2A09 (B) What brief statement indicates that you are listening on a repeater and looking for a contact? A. The words “Hello test” followed by your call sign B. Your call sign C. The repeater call sign followed by your call sign D. The letters “QSY” followed by your call sign
Gary/KN4AQ wrote this tongue-in-cheek article HamRadioNow: Do NOT Call CQ on Repeaters which says that calling CQ on a quiet repeater works well because it is likely that someone will come on and tell you not to call CQ. Gary wrote:
So I trot out my standard advice: make some noise. I even recommend calling CQ, because that’s almost guaranteed to get someone to respond, if only to tell you that you’re not supposed to call CQ on repeaters.
Some important things have changed in our use of VHF/UHF FM over past decades. The most important shift is dispersion of activity: while the number of VHF/UHF channels has increased, the total amount of VHF/UHF radio activity has declined. This means that we have tons of channels available that are mostly quiet. Tune the bands above 50 MHz and you’ll hear a lot of dead air. In response to this, some hams routinely scan multiple repeater and simplex frequencies. While getting ready for Summits On The Air (SOTA) activity, I’ve had hams ask me to make a long call on 146.52 MHz so they can be sure to pick me up on scan.
Another factor that comes into play is the multitasking nature of our society. Hams don’t generally sit in front of a 2m radio waiting for activity to occur. More commonly, they are doing something else and listening to the FM rig in the background. VHF FM is the Utility Mode, always available but not necessarily the top priority. A short call (“KØNR listening”) on the frequency can easily be missed.
Recommendations
My conclusion is that the Old School “KØNR Monitoring” style of making a call on VHF is no longer sufficient. First off, it sends the message of “I am here if you want to talk to me.” If that’s your intent, fine. However, if you really want to make a contact, being more explicit and a bit assertive usually helps. Follow Gary’s advice and make some noise.
For example, during a SOTA activation I’ll usually call on 146.52 MHz with a bit of a sales pitch. Something like: “CQ CQ 2 meters, this is Kilo Zero November Romeo on Pikes Peak, Summits On The Air, anyone around?” This is way more effective than “KØNR Monitoring.” I might also include the frequency that I am calling on, to help out those Scanning Hams. Something like “CQ CQ 146.52, this is KØNR on Pikes Peak, Summits On The Air.” Note that these calls are still pretty much short and to the point, only taking about 15 seconds. This is a lot shorter than the typical HF CQ.
If I am driving through another town and want to make contact on the local repeater, I will adjust my approach accordingly. For example, on a relatively quiet repeater, I might say “CQ, anyone around this morning? KØNR mobile I-25 Denver.” Or if I have a specific need, I’ll go ahead and ask for it. “This is KØNR looking for a signal report.”
Keep in mind that VHF/UHF operating tends to be local in nature, so it makes sense to adapt your approach to both local practice and the specific situation.
It’s OK to call CQ on VHF FM, make some noise on the frequency.
Give other operators a reason to contact you.
Don’t make your CQ too long, maybe 15 to 20 seconds.
When we teach our Technician License class, we normally differentiate between HF and VHF propagation by saying that HF often exhibits skywave propagation but VHF is normally line-of-sight. For the beginner to ham radio, this is a reasonable model for understanding the basics of radio propagation. As George E. P. Box said, “All models are wrong, but some are useful.”
In recent years, I’ve come to realize the limitations of this model and how it causes radio hams to miss out on what’s possible on the VHF and higher bands.
Exotic Propagation Modes
First, let me acknowledge and set aside some of the more exotic propagation modes used on the VHF and higher bands. Sporadic-e propagation allows long distance communication by refracting signals off the e-layer of the ionosphere. This is very common on the 6-meter band and less so on the 2-meter band. I like to think of this as the VHF bands trying to imitate HF. Tropospheric ducting supports long distance VHF communication when ducts form between air masses of different temperatures and humidities. Auroral propagation reflects the radio signal off the auroral ionization that sometimes occurs in the polar regions. Meteor scatter reflects signals off the ionizing trail of meteors entering the earth’s atmosphere. Earth-Moon-Earth (EME) operation bounces VHF and UHF signals off the moon to communicate with other locations on earth. These are all interesting and useful propagation mechanisms for VHF and higher but not the focus of this article.
Improved Line-of-Sight Model
Now let’s take a look at more “normal” VHF propagation that occurs on a daily basis, starting with the simple line-of-sight propagation model. The usual description of line-of-sight VHF is that the radio waves travel a bit further than the optical horizon (say 15% more) . Let’s refer to this as the Line-of-Sight (LOS) region where signals are usually direct and strong. What is often overlooked is that beyond the radio horizon, these signals continue to propagate but with reduced signal level. Let’s call this the Non-Line-of-Sight (NLOS) region. The key point is that the radio waves do not abruptly stop at the edge of the LOS region…they keep going into the NLOS region but with reduced signal strength. Now I will admit that this is still a rather simplistic model. Perhaps too simplistic. I’m sure we could use computer modeling to be more descriptive and precise, but this model will be good enough for this article. All models are wrong, but some are useful.
WORKING the LOS and NLOS Regions
Let’s apply the model for Summits On The Air (SOTA) VHF activations. If we are only interested in working the LOS region, we won’t need much of a radio. Even a handheld transceiver with a rubber duck antenna can probably make contacts in the LOS region. It’s still worth upgrading the rubber duck antenna to something that actually radiates to improve our signal (such as a half-wave antenna). We may pick up some radio contacts in the NLOS region as well but our success will be limited.
To improve our results in the NLOS zone, we need to increase our signal strength. We are working on the margin, so every additional dB can make enough difference to go from “no contact” to “in the log.” Think about another radio operator sitting in the NLOS zone but not quite able to hear your signal. Your signal is just a bit too weak and is just below the noise floor of the operator’s receiver. Now imagine that you improve your signal strength by 3 dB, which is just enough to get above the noise and be a readable signal. You’ve just gone from “not readable” to “just readable” with only a few dB improvement.
What can we do to improve our signal levels? The first thing to try is improving the antenna, which helps you on both transmit and receive. I already mentioned the need to ditch the rubber duck on your HT. My measurements indicate that a half-wave vertical is about 8 dB better than a typical rubber duck. This is only an estimate…performance of rubber duck antennas vary greatly. A small yagi (3-element Arrow II yagi) can add another 6 dB improvement over the half-wave antenna, which means a yagi has about a 14 dB advantage over a rubber duck.
On the other hand, if you believe that your VHF radio is only Line-of-Sight, then there is no reason to work on increasing its signal level. The radio wave is going to travel to anything within the radio horizon and then it will magically stop. This is the myth that we need to break.
More Power
When doing SOTA activations, I noticed that I was able to hear some stations quite well but they were having trouble hearing me. Now why would this be? Over time, I started to realize these stations were typically home or mobile stations running 40 or 50 watts of output. This created an imbalance between the radiated signal from my 5 watt handheld and their 50 watts. In decibels, this difference is 10 dB. Within the LOS region, this probably is not going to matter because signals are strong anyway. But when trying to make more distant radio contracts into the NLOS zone, it definitely makes a difference. So I traded my HT for a mini-mobile transceiver running 25 watts. See the complete story in More Power for VHF SOTA.
Weak Signal VHF
Of course, this is nothing new for serious weak-signal VHF enthusiasts. They operate in the NLOS region all of the time, squeezing out distance QSOs using CW, SSB and the WSJT modes. They generally use large directional antennas, low noise preamps and RF power amplifiers to improve their station’s performance. They know that a dB here and a dB there adds up to bigger signals, longer distances and more radio contacts. A well-equipped weak-signal VHF station in “flatland geography” can work over 250 miles on a regular basis…no exotic propagation required.
Now you might think that FM behaves differently, because of the threshold effect. When FM signals get weak, they fade into the noise quickly…a rather steep cliff compared to SSB which fades linearly. FM has poor weak-signal performance AND it fades quickly with decreasing signal strength. This is why it is not the favored modulation for serious VHF work. But the same principle applies: if we can boost our signal strength by a few dB, it can make the difference between making the radio contact or not.
So VHF is not limited to line-of-sight propagation…the signals go much further. But they do tend to be weak in signal strength so we need to optimize everything under our control to maximize our range.
Bob/K0NR operating from the summit of Genesee Mountain (W0C/FR-194)
For the ARRL January VHF contest, I did a combination Summits On The Air (SOTA) and contest entry. I am recovering from a knee injury so Genesee Mountain (W0C/FR-194) turned out to be a nice easy hike for me. Of course, Joyce/K0JJW joined me and also did a SOTA activation. Caleb/W4XEN came along with us and activated the summit for SOTA using the HF bands. Finally, Brad/WA6MM showed up on the summit for a social visit.
Hiking route to Genesee Mountain from lower parking area.
To get to the Genesee Mountain, go west on I-70 from Denver, take Exit 254 to the south. Turn right onto Genesee Mountain Road and head into Genesee Mountain Park. There is an extensive trail system in the park and several different ways to reach the summit of Genesee Mountain. In fact, if the gate is open, you can drive right to the summit. The route we took starts at a parking area that is always open. With only a 0.7 mile hike (300 feet vertical), this is an easy and highly-recommended trail.
Leaving the parking area going uphill, we soon encountered the Genesee Mountain Trail which we followed to the left. Later we transitioned to the Genesee Summit Trail, which goes to the summit. Both of these are well marked but you need to make sure you catch the “summit” trail.
This sign clearly marks the route to the summit trailA flag pole marks the summit.
We took more than the usual set of equipment for this activation so that we could cover the 6m, 2m, 1.25m and 70cm bands. For FM, we set up a Yaesu FT-90 2m/70cm transceiver with a ladder-line J-pole hanging from a rope in a tree. This omnidirectional antenna does not have any gain but I figured that for FM it would be most efficient to not mess with having to point a yagi antenna. For 2m and 70cm ssb/cw, I used a Yaesu FT-817 driving an Arrow II dualband antenna. The FT-817 also handled the 6m band, driving an end-fed half-wave wire antenna supported by a fishing pole (HF SOTA style). For the 1.25m band, I just used an Alinco handheld radio.
Caleb/W4XEN operating the HF bands for SOTA. Note the use of the SOTA flag to obtain an extra 2 dB of signal.
Genesee Mountain is a popular SOTA summit because it is so easy to access but still provides a good outdoor experience. We encountered a dozen of so hikers and mountainbikers on the summit and it can be very busy during a summer weekend. The summit is wide and flat with plenty of room to set up a portable station. For VHF, it has an excellent radio horizon to the front range cities.
Brad/WA6MM and Joyce/K0JJW on the summit.
Joyce made 14 contacts on 2m and 70cm FM. I made 52 QSOs, as shown in the table below. SSB activity was relatively light considering it was a VHF contest weekend. I was pleased to work Jay/W9RM in DM58 on 2m SSB at a distance of 167 miles. W9RM is on the other end of the state with many mountains blocking the path. I also worked Jim/WD0BQM in Mitchell, NE (DN81) on 2m CW, at a distance of 175 miles. VHF is not limited to line of sight!
Band Mode QSOs Pts Grd
50 USB 5 5 2
144 CW 1 1 1
144 FM 19 19 2
144 USB 7 7 2
222 FM 3 3 1
432 FM 15 30 2
432 USB 2 4 1
Total 52 69 11
Score : 759
We had a great day on the summit, operating for just under 4 hours (with lots of breaks along the way). Thanks to Caleb/W4XEN and Brad/WA6MM for joining the fun. If you are looking for your first or an easy SOTA activation, give Genesee a try.
One of our favorite summit hikes along the front range of Colorado is Devils Head lookout tower (W0C/FR-051). This hike is about 1.5 miles one way with 900 feet of vertical gain. See my summer trip report from July 2012 for more information on the hike. This year we activated the summit in winter.
The sign at the bottom of the steps leading to the fire lookout.
One problem with this trail is that it has become extremely popular in the summer months. The actual summit and lookout tower is not very big and can get very crowded. This is tolerable for hiking but can make a Summits On The Air (SOTA) activation difficult. It certainly is not a “get away from it all” experience.
Joyce/K0JJW and Bob/K0NR on the trail to Devils Head.
Recently, Brad/WA6MM pointed out that the summit is still accessible now (in late November) and the crowds have all disappeared. Note that the trailhead will be difficult to access starting December 1st (see the Devils Head forest service page).
Typical trail conditions for our hike.
We took highway 67 out of Sedalia, then south on Rampart Range Road (FS 300) to the well-marked side road that goes to the trailhead . The forest service roads had 6 to 8 inches of snow on them but we were able to drive our 4WD pickup truck to the trailhead without any problem. The trail was also snow covered but walking in high-top hiking boots worked just fine. We had our microspikes along in case of ice but did not use them.
View of the Devils Head lookout tower in winter.
As you can see from the photos, it was a bright sunny day…wonderful day to be out hiking in the mountains. Temperature was about 25 degrees F but very light wind.
View to the east from the summit of Devils Head.
We met a total of four other parties on the trail, so not very busy.
Once on top, we started calling on 146.52 MHz with many stations responding. That summit has good line-of-sight to Denver and the other front range cities. As things quieted down on 2 meters, I switched to 446.0 MHz and worked a bunch of stations there, too. We were using the small TYT 2m/70cm mobile transceiver (which I recently repaired) and yagi antennas for 2m and 70cm. I also had my 23cm HT and Comet yagi with me and managed to work Paul/W0RW on 1294.5 MHz, about 33 miles (53 km) away in Colorado Springs.
Here is my log from the activation:
Joyce worked a subset of these stations. In particular, she was very happy to work three women. She has been referring to these contacts as “F2F” for “female to female.” On this activation, her F2F QSOs were: Annette/KA0JKZ, Sharon/KC0PBR and Barbara/W0BJE. Way to go, ladies!
Bob/K0NR holding the 1.2 GHz Comet yagi antenna.
We’ve made a note to do this summit again next year, after the crowds are gone. It is a really nice early winter hike. Thanks to everyone that worked us on the summit.
Batteries are a necessity for portable operation, including Summits On The Air (SOTA) activations. In situations where I’m using a handheld transceiver, it has its own battery. I might carry a spare battery or two, depending on how long I intend to operate.
I also make use of my Yaesu FT-817 (mostly for 2m ssb/cw) and a small 2m/70cm FM transceiver (Yaesu FT-90). The FT-817 has an internal battery pack but I worry that it will run out of charge during the activation. The FT-90 needs a battery to function, drawing 9.5 A at full power. However, I usually run it at a lower power setting, probably drawing about 5 or 6 A.
Sealed Lead Acid Battery
Sealed Lead Acid batteries are a tried and true technology that is cost-effective and heavy.
I started out using a small sealed lead acid (SLA) battery. These use well-established battery technology that has stood the test of time. They are easy to charge and do a good job. But they are a bit heavy. Initially, I thought “what’s an extra pound or two in my backpack?” Later, I started looking around for something more compact and lighter. As backpackers and SOTA activators know, a pound here and a pound there means you up end up with a really heavy backpack.
Lithium Iron Phosphate Battery
Lithium Iron Phosphate batteries are compact and lightweight.
Many SOTA activators use lithium iron phosphate (LiFePo4) batteries that are commonly used for radio-controlled aircraft/vehicles. I bought two of these batteries (Zippy 4200) and a special charger that handles LiFePo4. These batteries are lightweight and have great power density. One charge handled several SOTA activations…I never ran out of power.
Two battery connections for LiFePo4: the charging connection that accesses each cell and the output connection that goes to the radio.
As shown in the photo, these battery packs have two connections: one for charging that accesses each cell individually and one for current output that you connect to your radio. I removed the output connectors that came installed and replaced them with PowerPole connectors.
These batteries worked pretty well for me. They had plenty of capacity and held their voltage nicely during discharge. Then one of the batteries failed early in life. (I think I was taking good care of them, too.) One annoying thing with these batteries is that the charger was relatively large and had a fragile adapter that connected to the battery charging port. (This allows one charger to handle a wide variety of battery packs.) This was not a problem at home but I found it to be a disadvantage when traveling.
Bioenno Power 12 Volt Series
When the Zippy battery failed, it caused me to look further for other options. I ended up adopting the Bioenno series of batteries, specifically their 12V series: 12V Series – LFP (LiFePO4) Batteries. These battery packs also use LiFePO4 cells, but the charging controller smarts are embedded into the battery pack. These packs also have short circuit protection which is an awesome safety feature for lithium batteries. This makes the battery pack friendlier to use but it does cost a bit more. They also come with PowerPole connectors installed (along with another connection for the charger).
Our 12V LFP Lithium Iron Phosphate batteries give you the following advantages:
We guarantee our entire battery range comes with built-in protection-circuit-modules (PCM) micro-computers that internally balanced cells and confer protection including from overcharge, overdischarge and short circuiting.
A Bioenno Power battery is thermally and chemically stable
A Bioenno Power battery is dependable and reliable without the possibility of lithium fires
A Bioenno Power battery is 50% to 70% lighter than a traditional SLA (sealed lead acid) battery
A Bioenno Power battery allows for extraction of >80-90% of the rated capacity, whereas an SLA battery only allows for 50% of the rated capacity
A Bioenno Power product has a service life of 2000+ charge cycles at 5-10+ years with a shelf life that far exceeds the service life of many other batteries
Bioenno 4.5 Ah battery pack.
I bought two of their battery packs. The 4.5 Ah pack is for normal SOTA use, small and lightweight (1 pound). The second pack is 9 Ah for when I’m operating for a longer time (weighs 2.6 pounds), such as mountaintopping for a VHF contest. The Bienno 2A charger, which has a nice compact form factor, works with both of them. This charger is much better for packing up when traveling.
Larger Bioenno Power Battery (9 Ah)
The Bioenno 2A charger works with both battery packs.
I have used the Bioenno batteries on several SOTA activations and I’m quite happy with the setup. The Zippy LiFePO4 (and Sealed Lead Acid) are fine to use but I have found that the Bioenno system is superior overall. I will probably add a few more Bioenno battery packs to my collection over time. They make some really large batteries that would be good for EmComm work, but too heavy for hiking.
That’s my story on battery packs. What are you using?
The summit of Selun (HB/SG-049), left of center, viewed from the trail.
Joyce/K0JJW and I were planning a trip that included some time in Europe. It turned out that our airline route would connect through Zurich. Rather than spend a few hours in an airport, we decided to spend a day or two in Switzerland.
Somehow the discussion turned to Summits On The Air (SOTA) and whether we should do an activation in Switzerland. Slowly, a plan developed to do a “check the box” activation on a local summit near Zurich. As readers of this blog know, I’ve been exclusively using VHF/UHF for SOTA activations. We decided to pack really light so SOTA gear on this trip was extremely limited: 2m/70cm handhelds and vertical antennas. Sorry, no yagi.
The super-compact, multi-op VHF SOTA kit: two FT-1DR transceivers, two RH770 antennas and a charger.
SOTA Help
I came across this thread about the proper callsign prefix when operating under CEPT rules in Switzerland. The SOTA association is called HB but valid callsign prefixes are HB9 (full license) or HB3 (novice license). This sent me back to the CEPT rules to make sure I understood them correctly: Recommendation T/R 61-01 and ECC Recommendation (05) 06. The short story is that as an Amateur Extra licensee, I operate as HB9/K0NR. Joyce has a General Class license which corresponds to the “novice” category under CEPT, so she uses the callsign HB3/K0JJW. Apparently as an Extra, I had previously overlooked or forgotten some of the fine points of CEPT. Specifically, US Extras are given full privileges by CEPT but Generals can only operate in a subset of CEPT countries while Technicians get no privileges at all (yet another reason to upgrade your license).
Joyce/K0JJW and I have one day in Zurich later this month. Somehow the idea of squeezing in a SOTA activation while in Switzerland made it onto the itinerary.
This will be on 2m FM only with basic gear. The current plan is looking like a hike up Altberg (HB/ZH-015) but we are open to other ideas.
A number of people responded with helpful information. Soon I was contacted by Paul/HB9DST who suggested we do an activation together. Paul is an American living just outside of Zurich (his US callsign is AA1MI) and is very active in SOTA. We soon had our eyes on the Churfirsten SOTA summits which are southeast of Zurich (see Paul’s activation reports). Ultimately, we chose the summit of Selun (HB/SG-049). Clearly, this was a huge upgrade to a classic Swiss mountain (compared to our original plan).
Activating Selun (HB/SG-049)
Selun (HB/SG-049) is east and a bit south of Zurich by 35 miles (56 km), as indicated in the lower right corner of the map.
Access to the trail was via several train rides and a bus ride (about 2 hours), then a short walk to the Selun cable car. This cable car is quite unique in that it is a homebrew design (see the photo below). We piled into the cable car and rode it to where the real hike started.
The Selun cable car is a bit of a homebrew device but perfectly safe. As far as we know.
Joyce/K0JJW and Bob/K0NR riding the cable car.
On the Trail
The bottom station of the cable car is at ~3000 feet (900 m) which took us up the hill to ~5000 feet ( 1500 m), so it definitely sliced off some elevation gain. The summit of Selun is at 7234 feet (2205 m), which gave us a moderate but not crazy difficult hike. My GPS app recorded a distance of 1.7 miles and 1900 vertical feet (one way).
Our hiking route is shown in blue ascending the summit from the north. There are six other SOTA summits on the same ridge, marked by waypoints on the map.
We were treated to wonderful views on the hike, often with clouds laying low in the valley.
The weather was excellent for late October with blue skies above and some clouds laying in the valleys.
Joyce/K0JJW working 2m fm with Paul/HB9DST cranking out the CW contacts in the background.
Paul is an HF/CW enthusiast so that made sharing the bands very easy. He strapped his fishing pole to the summit cross and strung out an end-fed wire for 40m, 30m and 20m, making a total of 40 QSOs. Joyce and I took turns on 145.550 MHz FM using our Yaesu FT-1DR handheld radios with vertical antennas.
Paul/HB9DST working HF CW on the summit.
Bob (HB9/K0NR) operating 2m fm from the summit of HB/SG-049.
I made 13 contacts on VHF, including three Summit-to-Summit (S2S) contacts. HB9PMF was close by on SG-017 (Hinterrugg), another summit in the Churfirsten. I also stayed on the summit while Joyce and Paul hiked down out of the activation zone so they could work me for chaser points, giving me a total of 15 QSOs.
My log is shown below. All contacts were on 145.550 MHz. Note that the calling frequency in Switzerland (all of Europe?) is 145.500 MHz. Joyce worked a subset of these stations.
The HB9/K0NR/P log from HB/SG-049
Operating notes
I have to admit that it was a challenge keeping everything straight while making QSOs. I had to add the HB9 prefix on the front of my US callsign and “portable” on the tail end (local practice for activator stations). That’s “HB9/K0NR/P” instead of just “K0NR”…there is a reason we prefer shorter callsigns. All that along with the usual signal report, name, SOTA designators, etc. Fortunately, everyone we worked had reasonable English skills. Mein Deutsch ist nicht so gut. If I sounded a bit confused, I probably was and at only 7200 feet I can’t blame the altitude.
It was definitely a thrill to work the S2S stations and two other countries (Germany and Austria) on VHF. (I have never done that on SOTA VHF from Colorado…I rarely work anyone outside of the state.)
Bob/K0NR and Paul/HB9DST enjoying refreshments after the hike.
After we hiked back down, Paul suggested that we had to stop in at the local farmhouse restaurant (Selun Ochsenhuette) for a drink. It was all part of the Swiss SOTA experience!
Paul was a magnificent host for our short stay in Switzerland. We stayed two nights at his place and he guided us on a fantastic SOTA activation. Without his help, we would have probably activated a small summit near Zurich and would have been in the low clouds all day. We would have left the city thinking “I bet this is a beautiful place when the sun is shining.” Instead, we had an excellent day hiking the Swiss mountains and playing ham radio. Thanks, Paul!
Joyce is showing off her sewing project — a SOTA Mountain Goat patch on Paul’s backpack.
Joyce did find one small way to repay Paul’s kindness. Being an skilled seamstress, she sewed Paul’s prized SOTA Mountain Goat patch onto his pack. Nice job, Joyce!
Early on, she always hiked with me on SOTA activations but didn’t start pursuing activator points until the middle of 2017. All of her SOTA contacts have been on the VHF/UHF bands, lots of 2m FM along with 2m SSB, 70 cm and 23 cm FM.
